Hello,
My reader stuck on boot and I my idea how to bring it to live also. I replaced memory card, restore four partitions structure and fill it data which I restored from damaged card. Then I make update firmware with success. Then reader stuck on boot in place as picture. I connected serial port monitor to it and in attachment is what he said. I tried to patch monitor.app with new CID of card as tutorial on this forum but he still is the same place. What is the reason that boot log include some errors?
My reader stuck on boot and I my idea how to bring it to live also. I replaced memory card, restore four partitions structure and fill it data which I restored from damaged card. Then I make update firmware with success. Then reader stuck on boot in place as picture. I connected serial port monitor to it and in attachment is what he said. I tried to patch monitor.app with new CID of card as tutorial on this forum but he still is the same place. What is the reason that boot log include some errors?
Code:
▒▒
U-Boot 2009.08 (Jul 15 2016 - 16:04:21)
CPU: Freescale i.MX6 family TO0.0 at 792 MHz
Temperature: 33 C, calibration data 0x5764f75f
mx6q pll1: 792MHz
mx6q pll2: 528MHz
mx6q pll3: 480MHz
mx6q pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 24000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
epdc_axi sel=5 podf=2
epdc_pix sel=5 pred=1 podf=0
Board: MX6SoloLite-NTX:[ POR ]
Boot Device: SD
I2C: ready
DRAM: 512 MB
MMC: loading ntx config
ram p=80000000,size=536870912
csd is 0x400e0032, 0x5b590000, 0x747b7f80, 0xa400000
scr addr is 0x875feef0, switch_status addr is 0x875fee80
mmc0 is current device
MMC read: dev # 0, block # 1023, count 1 ... 1 blocks read: OK
MMC read: dev # 0, block # 1024, count 1 ... 1 blocks read: OK
FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2
i2c: I2C1 SDA is low, start i2c recovery...
I2C1 Recovery success
i2c: I2C2 SDA is low, start i2c recovery...
I2C2 Recovery success
hw_anadig_reg_core=7c3e1f
setup_epdc() 1448x1072
EPDPMIC_VIN=1
*** Warning - bad CRC or MMC, using default environment
In: serial
Out: serial
Err: serial
ntx_hw_late_init()
MMC read: dev # 0, block # 1, count 1 ... 1 blocks read: OK
NTXSN:"NX170000000000000000"
REGISET2 val E0
RC5T619 read battery temperature 1235mV (0x7E7).
ntx_detect_usb_plugin():Charge detecting ............................set 900mA for DCP (26)
Battery OK, voltage 4008mv, charger ON
resolution 1448x1072, bpp 8, pixclk 80000000
waveform is at 88600000, size 241432, 472 blocks
vcom=-2220
Draw normal logo: offset 55296
Splash loaded at 88a00000
** bitmap 1072x1448
waveform buffer addr = 88600000
EPDC init ok
EPDPMIC_VIN=1
tps65185_rail_power_onoff() TPS65185 wakeup
tps65185_rail_power_onoff() TPS65185 Enable RAIL POWER
epdc_power_on : waiting for epd power on ...ok. cnt=9720
EPDPMIC_VCOM=1
Draw_splash_screen
Device: FSL_USDHC
Manufacturer ID: fe
OEM: 3432
Name: SD16G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
Clock: 50000000
High Capacity: Yes
Capacity: 15634268160 Bytes
Bus Width: 4-bit
Boot Partition for boot: No boot partition available
csd is 0x400e0032, 0x5b590000, 0x747b7f80, 0xa400000
scr addr is 0x875fef58, switch_status addr is 0x875feee8
ntx_config_fastboot_layout():8 binaries partition added
ntx_config_fastboot_layout():2 mbr partition added 0
hwcfgp=9ffffe00,pcb=61,customer=0
ESDin=0,UPGKey=0,PWRKey=0,USBin=0x1,BootESD=0,MenuKey=0
Kernel RAM visiable size=511M->511M
MMC read: dev # 0, block # 2047, count 1 ... 1 blocks read: OK
kernel size = 2837928
MMC read: dev # 0, block # 2048, count 5549 ... 5549 blocks read: OK
hwcfg partition type : 0
Splash screen update - Waiting for LUT to complete......................... OK
## Booting kernel from Legacy Image at 80007fc0 ...
Image Name: ?_#1 Oct 31 13:23:18
Created: 2019-10-31 11:23:25 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2558472 Bytes = 2.4 MB
Load Address: 80008000
Entry Point: 80008000
Loading Kernel Image (80008000->80008000) ... OK
OK
Starting kernel ...
--
rm /mnt/secure/debug_mode to disable debug
Check Network Manager Status
Atached mp shm: id 0 addr 2d144000 size 21736
epdc_default_init
epdc_default_rotate: w=1072 h=1448 scan=1088 mem=1695744
program_name = [./pocketbook], basename = [pocketbook], init_string = [/P7.Sink=Null /P7.Pool=128 /P7.Format="{%ts}[%fs:%fl] %lv %ms"]
program init string = [(null)]
default init string = [(null)]
[748 : ./pocketbook] (open_mqueue)cannot attach to message queue[hw_ipcrequest_to] msgsnd error: Invalid argument
hw_eink_init: could not get current task
[hw_ipcrequest_to] msgsnd error: Invalid argument
Process has been terminated by signal {SIGSEGV::SEGV_MAPERR}
Segmentation fault
Please press Enter to activate this console. Start Network Manager
[766:01/01/12 00:00:06] netagent called with parameters < net on >
[766:01/01/12 00:00:06] bringing up wifi
Failed to connect to non-global ctrl_ifname: eth0 error: No such file or directory
Successfully initialized wpa_supplicant
rfkill: Cannot open RFKILL control device
Network Manager checker work done